Elastoflex VP ULTRA

Elastoflex VP Ultra is a smooth surface Elastomeric (SBS) modified bitumen roofing membrane reinforced with a high performance fiberglass and polyester composite reinforcement that provides flexibility and dimensional stability as well as excellent tear and puncture resistance.

Elastoflex VP Ultra is designed for use as a mechanically attached base sheet in multi-layer low-slope assemblies. Polyglass self-adhered Dual-Match Selvage Edges are manufactured on the opposing sides of the top and bottom surfaces of the membrane. These unique selvage edges are 100% covered with Polyglass’ patent pending SEALLap ULTRA technology which applies a very aggressive self-adhering (SA) compound. This feature provides an immediate waterproofing seal at the laps, including sealing around properly installed plates and fasteners, without adding external heat from torches or hot-air guns. Contractors save labor, time, and equipment expenses. Align – roll – done!

Elastoflex VP Ultra has film surfaces on the top and bottom which enables successive system layers to be heat welded using an additional ply of Elastoflex S6, or a finishing ply of Elastoflex S6 G or other Polyglass torch cap sheets. The selvage edges are protected by siliconized release films that protect the self-adhering compound from contaminants and are easily removed during installation.

ELASTOFLEX S6 25

Elastoflex S6 25 is a smooth surface Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane reinforced with a polyester mat saturated with a rubberized asphaltic compound. The non-woven reinforcement provides superior tear strength and puncture resistance.

Elastoflex S6 25 is designed for use as a base ply or interply layer in multi-layer low-slope assemblies, and is available in a film or sand top surface and a film or sand bottom surface.

Application methods include hot asphalt or cold adhesive when the membrane is sand backed. When a top surface film configuration is selected, successive system layers can be heat welded with an additional ply of Elastoflex S6 25, Elastoflex S6 G or other Polyglass SBS cap sheet. A top film configuration also allows for the application of a variety of Polyglass SBS or APP self-adhered cap sheets.

Elastoflex V

Elastoflex V is a high quality, fiberglass reinforced, SBS (Styrene-Butadiene-Styrene) modified bitumen roofing membrane. Elastoflex V is specially designed with a sand surface and either a sand back (for hot mop or cold process applications) or with a polyethylene burn-off film (for heat weld applications). Reinforced with a superior fiberglass mat, the Elastoflex V exhibits exceptional dimensional stability and puncture resistance. Manufactured for the commercial, industrial and residential markets, the proprietary SBS compound will offer long term performance and can be warranted as part of an approved Polyglass assembly.

Elastoflex S6 22

Elastoflex S6 22 is a smooth surface Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane reinforced with a polyester mat saturated with a rubberized asphaltic compound. The non-woven reinforcement provides superior tear strength and puncture resistance.

Elastoflex S6 22 is designed for use as a base ply or interply layer in multi-layer low-slope assemblies, and is available in a film or sand top surface and a film or sand bottom surface.

Application methods include heat welding, when a film bottom surface is selected, and hot asphalt or cold adhesive when the membrane is sand backed. When a top surface film configuration is selected, successive system layers can be heat welded with an additional ply of Elastoflex S6 22, Elastoflex S6 G or other Polyglass SBS cap sheet. A top film configuration also allows for the application of a variety of Polyglass SBS or APP self-adhered cap sheets.

Elastoflex V HP

Elastoflex V HP is an SBS (elastomeric) modified bitumen roofing membrane base sheet. This durable membrane is reinforced with a high performance fiberglass mat to ensure exceptional strength and dimensional stability to the product. The proprietary SBS compound offers superior waterproofing and weathering physical properties.
Elastoflex V HP is intended for use as a base ply or interply membrane and designed to be installed in mechanically attached or heat-welded. Elastoflex V HP can be used as a part of a Polyglass multi-ply system, when combined with Elastoflex V G HP FR cap sheet or other approved Polyglass cap sheets.

Elastoflex V 22

Elastoflex V 22 is a Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane base sheet. This higher quality membrane is reinforced with a high quality fiberglass mat to ensure strength and excellent dimensional stability to the product. Elastoflex V 22 exhibits superior waterproofing and weathering physical properties.

The top and bottom surfaces are available in sand or factory applied burn-off film. Application methods include mechanically attached, hot asphalt, heat-welded, or as part of cold-applied system. When the top of membrane is surfaced with film, Elastoflex V 22 can be used as a base sheet in self-adhered systems.

Elastoflex V 22 membrane can be used as part of a Polyglass warranted multi-ply system, when combined with Elastoflex V G cap sheets or other approved Polyglass base sheets.

Polyflex®

Polyflex is an Atactic Polypropylene (APP) modified bitumen roofing membrane reinforced with a superior non-woven polyester mat that provides flexibility and dimensional stability as well as excellent tear and puncture resistance. The premium APP compound and durable construction provides long-term weathering performance. Polyflex is designed for use as base, interply, or cap sheet in multilayer low-slope assemblies.

The top is constructed with a smooth sand surface while the bottom has a factory applied burn-off film for heat welding applications.

Successive system layers can be heat welded with an additional ply of Polyflex or Polyflex G cap sheets. Polyflex is an approved mechanically attached base sheet for the Velociflex system.

Elastobase® P

Elastobase P is a high quality Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane reinforced with a strong non-woven polyester mat that provides flexibility and dimensional stability as well as excellent tear and puncture resistance. The proprietary SBS compound offers quality waterproofing and weathering physical properties. Elastobase P is designed for use as a base ply layer in multi-layer low-slope assemblies.

Elastobase P is available in sand or factory applied burn-off film on both top and bottom surfaces. Application methods include mechanically attached, hot asphalt, heat-welded, or as part of cold-applied system. When the top of membrane is surfaced with film, Elastobase P can be used as a base sheet in self-adhered systems.

Elastobase P can be used as part of a Polyglass warranted multiply system when combined with a variety of Polyglass base sheets and cap sheets.

Elastovent®

Elastovent is a Styrene-Butadiene-Styrene (SBS) modified bitumen base sheet for multi-ply low-slope roofing assemblies where venting of the substrate is desired. Venting is accomplished by the granule underside surfacing facilitating airflow between the bottom of membrane and substrate. A heavy duty fiberglass reinforcement provides a strong and dimensionally stable substrate for other roofing membrane plies. The top surface of membrane is sand, allowing for cold adhesive, heat welding or hot mopping an approved Polyglass base or cap sheet.

Elastoflex S6

Elastoflex S6 is a smooth surface Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane reinforced with a polyester mat saturated with a rubberized asphaltic compound. The non-woven reinforcement provides superior tear strength and puncture resistance.

Elastoflex S6 is designed for use as a base ply or interply layer in multi-layer low-slope assemblies. Membrane is available in a film or sand top surface and a film or sand bottom surface.

Application methods include heat welding, when a film bottom surface is selected, and hot asphalt or cold adhesive when the membrane is sand backed. When a top surface film configuration is selected, successive system layers can be heat welded with an additional ply of Elastoflex S6, Elastoflex S6 G or other Polyglass SBS cap sheet. A top film configuration also allows for the application of a variety of Polyglass SBS or APP self- adhered cap sheets.

Elastoflex S6 is an approved mechanically attached base sheet for the Velociflex system.

Elastoflex S6 HP

Elastoflex S6 HP is a smooth surface Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane reinforced with a polyester mat saturated with a rubberized asphaltic compound. The non-woven reinforcement provides superior tear strength and puncture resistance.

Elastoflex S6 HP is designed for use as a base ply or interply layer in low-slope assemblies, and is available in a film or sand top surface and a film or sand bottom surface.

Application methods include heat welding, when a film bottom surface is selected, and hot asphalt or cold adhesive when the membrane is sand backed. When a top surface film configuration is selected, successive system layers can be heat welded with an additional ply of Elastoflex S6 HP, Elastoflex S6 G HP, or other Polyglass SBS cap sheet. A top film configuration also allows for the application of a variety of Polyglass SBS or APP self-adhered cap sheets.

Elastoflex S6 HP is an approved mechanically attached base sheet for the Velociflex system.

Elastoflex V

Elastoflex V is a Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane base sheet. This higher quality membrane is reinforced with a high quality fiberglass mat to ensure strength and excellent dimensional stability to the product. Elastoflex V exhibits superior waterproofing and weathering physical properties.

The top surface is available in sand or film and the bottom surface is a factory applied burn-off film. Application methods include mechanically attached, hot asphalt, heat-welded, or as part of cold-applied system. When the top of membrane is surfaced with film, Elastoflex V can be used as a base sheet in self-adhered systems.

Elastoflex V membrane can be used as part of a Polyglass warranted multi-ply system, when combined with Elastoflex V G cap sheets or other approved Polyglass base sheets.

Elastobase® V

Elastobase V is a high quality Styrene-Butadiene-Styrene (SBS) modified bitumen roofing membrane reinforced with a high quality fiberglass mat which provides strength and excellent dimensional stability. The proprietary SBS compound offers quality waterproofing and weathering physical properties. Elastobase V is designed for use as a base ply layer in multi-layer low-slope assemblies.
The top and bottom surfaces are available in sand or factory applied burn-off film.

Elastobase V is intended for use as a base ply or interply membrane and designed to be installed in mechanically attached, hot asphalt, heat-welded, or as part of cold-applied system. When the top of membrane is surfaced with film, Elastobase V can be used as a base sheet in self-adhered systems.

Polybase V

Polybase V is an Atactic Polypropylene (APP) modified bitumen roofing membrane base sheet, reinforced with a fiberglass mat. The proprietary APP compound offers quality waterproofing and weathering physical properties. Polybase V is designed for use as a base ply or interply layer in multi-layer low-slope assemblies.

The top and bottom surfaces of Polybase V are finished with polyolefin film. Application methods include mechanically attached or heat-welded. Successive system layers can be heat welded with a ply of Polyflex or Polyflex G cap sheets.

Polyanchor® UDL 40 – Discontinued

Polyanchor® UDL 40 is an Atactic Polypropylene (APP) modified steep slope underlayment constructed with a fiberglass reinforcement. A specialized aggregate is embedded on the walking surface for skid resistance. Utilizing our patented ADESO® dual compound technology, the top layer is APP modified and the bottom surface is a proprietary SBS modified compound. This feature gives the membrane all the benefits of APP plus selfsealing properties around properly installed nails. The bottom surface is sanded to protect the self-sealing compound and to keep the roll in place for accurate alignment and preparation for nailing after roll-out.